VeriCUT table with special custom design to allow the caterpillar track to run beneath the machine. VeriCUT can design the table to suit your special situation, whether it is size related, a special pit to have the table recessed into the floor, or special zoning for an existing dust collector.

Dust Collectors in VeriCUT downdraft tables drawing, draw smoke from cutting torch

VeriCUT downdraft tables are zoned to allow your dust collector to draw smoke only from the area where the torch is cutting. In fact VeriCUT builds these zones to be superbly maintenance free by using a patented special cantilever system so that your system uses no power, air supply or electrical actuators to open and close the zones. Plus we build the tables like tanks to give you decades of trouble-free plate cutting.

The following 24 foot x 13.3 foot downdraft system shipped to Illinois USA July 21st to a prestigious client’s showroom. The VeriCUT design along with customer’s slat frame concept allows lasers to cut with up to 10 kilowatts of power through 2-inch thick steel plate.

“New since 2016!” Manual downdraft mini-tables for small shops and special welding or handheld plasma cutting applications.

Downdraft table system 16 feet wide by 66 feet long for a laser cutting machine installation in Minnesota.

Here is a close up of operator working on the side operator. Note how zero smoke is occuring while plasma cutting and piercing is taking place.

Caterpillar track cabling tucked under table

Customization showing a Caterpillar Track placed under the table saving floor space!

Here we have a 10.5ft wide cutting table used in a coil line to cut holes in a US coil processing plant.

In this photo is an 11 foot by 48 foot downdraft VeriCUT system on Messer MG plasma cutting system.

VeriCUT can design a table to fit your needs, here we have an 80 foot VeriCUT system end view.

Pictured here, A VeriCUT system beneath an Messer MG plasma system.

Pictured here, the activation side of table showing the zoning and activation arms that open and close each individual section.

In this phos is a large 12 foot x 200 foot system for multiple machine plasma cutting and beveling.

VeriCUT cutting table, clean of smoke and dust, with walkway designed to protect plasma machine operator from cutting sparks

A plasma machine operator is using the VeriCUT table system. We are proud to show there is almost no smoke!

Pictured here, a VeriCUT downdraft cutting system for laser cutting with 5, 6, 8 and 10kW.

Pictured here, a spark trap on exhaust end of plasma table.

In this photo, a system is being installed just before inserting material support slats into the slat frames.

Pictured here is a stunning capture of the downdraft cutting tables high-efficiency smoke and dust removal systems for laser, plasma, and oxy-acetylene cutting.

Downdraft tables are work benches with built-in ventilation systems that capture and draw smoke, fumes and/or dust away from workers and materials being worked on.

The zone-by-zone ducting design means that your dust collection system draws only from the immediate area affected by cutting at that moment, drastically reducing capacity and energy requirements.

A dust collection system is used to enhance the quality of air released from industrial or commercial processes by collecting airborne particles, fine dust particles and impurities.

A downdraft table is a workspace that doubles as a proper waste disposal. There are many health-related hazards that come from breathing in dust and smoke (lung and throat cancer, continuous coughing and sneezing attacks, throat phlegm, asthma, and eye irritation). Therefore, proper dust collection has many good returns on the initial investment

A dust-free environment will result in higher product quality through avoiding rejects, rework, and lost production time. WIth a good dust collection system, you can breathe easier and enjoy both short and long term savings!

Built for long, dependable service with lower operating costs. Mechanical zone activation – no expensive electronics, hydraulics or pneumatics with Removable slag trays reduce maintenance downtime by up to 400%.

A water table built for one of the VeriCUT OEM accounts. This table incorporates built-in side rails for the customer’s plasma gantry to run on. Photo courtesy of Messer Cutting Systems Canadian Service Group, Automated Cutting Machinery Inc.

Gallery